ADEMCO Vista-50 Manuel d'utilisateur Page 89
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
– 77 –
NOTE:
The tamper switch need not be
used for UL Household Fire or
Burglary installations. The
tamper switch must be
connected to an EOLR
supervised zone programmed
for trouble by day/alarm by
night (type 05) response as
shown for UL Commercial
Burglary installations.
When the keyswitch is
removed from the wall, the
tamper switch will open causing
a fault (trouble or alarm) on
zone 6 and causing the panel
to disable keyswitch operation
until the partition is disarmed
from a console.
RED
820ohms
YELLOW
RED
(ARMED)
BLACK
820ohms
WHITE
GREEN
(READY)
TAMPER SWITCH
(CONTACTS CLOSE WHEN
SWITCH DEPRESSED. SEE NOTE)
BROWN BROWN
BLUE BLUE
LOCK SWITCH
(NORMALLY OPEN)
2K EOLR
2K EOLR
TO AUX POWER
(TERMINAL 6)
TO J7/OUT 2
TO ZONE 7(+)
(TERMINAL 20)
TO ZONE 6(–)/ZONE 7(– )
(TERMINAL 19)
TO ZONE 6(+)
(TERMINAL 18)
TO J7/OUT 4
BROKEN LINES REPRESENT
INSTALLER WIRING CONNECTIONS
Figure 23. Remote Keyswitch Wiring
3. Connect the keyswitch Armed and Ready LEDs to the trigger connector as
shown in
Figure 23
.
Programming The Remote Keyswitch
1. With at least one two-line alpha keypad (5137AD/6139) wired and set to a
proper address, power up the system temporarily by plugging the AC
transformer into a 120VAC outlet (previously wired to the control).
2. Enter data field programming mode: [Installer Code] + 8 0 0.
Program the following data fields:
*15 KEYSWITCH ASSIGNMENT for the partition in which the keyswitch is
used.
*40 OPEN/CLOSE REPORTING FOR KEYSWITCH as desired. The
keyswitch reports as user "0."
The system automatically assigns Zone Type 10 to Zone 7 if a keyswitch is
enabled.
3. Press *99 to exit program mode..
If you need more information about actual programming procedures, see Section
4:
THE MECHANICS OF PROGRAMMING.
LED indications are defined as follows:
Green Red Meaning
Off Off Disarmed & Not Ready
On Off Disarmed & Ready
Off On Steady Armed Away
Off Slow Flash Armed Stay
Off Rapid Flash Alarm Memory
- VISTA-50P 1
- VISTA-50PUL 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 8
- HOW TO USE THIS MANUAL 9
- Polling Loop Expansion: 13
- Wireless Expansion: 13
- Wireless Expansion 13
- Device Programming Mode 14
- Common Lobby Logic 17
- DATA FIELD 17
- DESCRIPTIONS) 17
- COMMON LOBBY 19
- Figure 3 24
- Figure 4 24
- TRIGGERS 25
- Figure 5 25
- Figure 6 26
- POWER-UP PROCEDURE 27
- SPECIFICATIONS AND 32
- ACCESSORIES 32
- Figure 8 33
- IMPORTANT: 34
- Figure 10 38
- Figure 9 39
- FINAL POWER UP 39
- PROCEDURE 39
- Figure 11 39
- VOLTAGE TRIGGERS 41
- Figure 12 41
- Wire Gauge Max. Length 45
- #22 gauge 650 feet 45
- #20 gauge 950 feet 45
- #18 gauge 1500 feet 45
- #16 gauge 2400 feet 45
- FINAL POWER-UP PROCEDURE 46
- FINAL POWER UP PROCEDURE 47
- (5700/5800 series) 53
- Figure 15 55
- Device Programming 55
- Programming 56
- House ID 57
- Device Address 57
- PROGRAMMING WIRELESS ZONES 58
- Go/No Go Test Mode 67
- Transmitter ID Sniffer Mode 67
- Programming Options Defined 68
- Time Driven 68
- 4204 RELAY MODULE 69
- restores 71
- STOP (STP): 72
- SCHEDULING OPTIONS 74
- (VIP) MODULE 77
- VOICE MODULE 79
- #93 MENU MODE PROGRAMMING 80
- DEVICES 80
- Section 11 81
- Figure 19 82
- MODEL EAGLE SECURITY 83
- AUDIO ALARM VERIFICATION 84
- Figure 20 84
- 1 2 3 4 5 6 7 8 9 85
- J7 CONNECTOR 86
- 4142TR CABLE 86
- RELAY OUTPUTS AND POWERLINE 87
- CARRIER DEVICES 87
- Figure 23 89
- 2.8A maximum 91
- Figure 26 92
- Section 14: EVENT LOG OPTIONS 94
- SETTING THE REAL TIME CLOCK 95
- CLEAR EVENT LOG 97
- 0=NO 1=YES 97
- Figure 28 98
- Figure 29 98
- NO CONNECTION 99
- RED (+)BLK (–) 99
- THE MECHANICS OF PROGRAMMING 100
- Battery Calculation Worksheet 101
- 95 96 99 107
- 109
- 109
- 12345678 112
- 95 96 99 Duress 113
- 119
- ZONE PROGRAMMING 121
- PROGRAMMING 121
- ALPHA PROGRAMMING 121
- ZONE TYPE DEFINITIONS 121
- ∗) to exit back to normal 122
- CHARACTER (ASCII) CHART 129
- to exit Menu Mode 131
- * to accept entry 132
- Number (HH:MM) (HH:MM) 140
- Hol. Partition 143
- Mon/Day 1 2345678 143
- HOLIDAY NUMBER ? 143
- Action Codes: 146
- 01 RELAY GRP # ? 146
- GROUP ? 12345678 147
- ACCESS SCHED # ? 148
- MON A1 Window 1? 148
- MON A1 Window 2 ? 148
- 06 ENTER OUTPUT# 151
- 06 Days? MTWTFSS 152
- ], or [A] = 95;Duress = 92 154
- NOTES Note: Low Speed will 157
- Other brands are not 162
- Summary of Connections 165
- LOG PRINTER CONNECTIONS 165
- Auth Title 167
- Section 25: KEYPAD FUNCTIONS 173
- ENTER DEVICE NO 177
- REGULATORY AGENCY STATEMENTS 182
- IMPORTANT 188
- SET SWITCHES WITH 188
- BATTERY REMOVED 188
- SUMMARY OF SYSTEM COMMANDS 189
- SPECIFICATIONS 190
- CONTACTING TECHNICAL SUPPORT 191
- WARNING! 194
- N5945-6V2 2/98 195
- N5944-6V1 Rev B 4/99 196
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50
(132 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.169 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels