ADEMCO Vista-50 Manuel d'utilisateur Page 177
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
– 165 –
To program that speed key sequence, type the following :
*2 D 61011 D 4D*1 D D
Note that the "D" key is pressed after the "2," the last "1" and the "4," separating
the different commands. Press "D" twice to complete the entry and exit.
To execute a speed key sequence, press the "D" key. The following appears:
ENTER USER CODE
****
Enter your user code. The programmed speedkey sequence will begin
automatically.
When defining speedkey sequences, do not use the [#] key to represent Quick
Arming. The system uses the code entered in response to the prompt to initiate
commands in a speedkey sequence, so the quick arm key is unnecessary. The
system interprets the use of the [#] key in a speedkey sequence as its designated
function only (e.g. #2 is not interpreted as arm in away mode, but rather as enter
house ID sniffer mode).
Manual Relay Activation Mode (#70 Mode)
The system allows users to manually activate relays/X-10 modules by keypad
command using either the keypad or a telephone keypad (if VIP module is used).
The user will be prompted (either by keypad alpha display or telephone voice
module).
To activate relays from a keypad, enter 4-digit security code + [#] +70.
To activate relays using a telephone and VIP module, first dial the 2-digit phone
access code. When the system acknowledges the access, enter 4-digit security
code + [#] + 70. The following prompts/voice responses will begin.
ENTER DEVICE NO.
00=QUIT 01
Voice: "ENTER DEVICE CODE NOW"
Enter the 2-digit number of the relay/X-10 module to be
activated.
nn DEVICE IS OFF
HIT 0=OFF , 1=ON
Voice: "
voice descriptor
DEVICE nn ON/OFF. FOR
voice descriptor
ON ENTER 1, FOR
voice descriptor
OFF ENTER 0"
Press 0 or 1 to turn the device off or on respectively.
"nn" represents the 2-digit relay/X-10 module number
and
voice descriptor
is the relay voice descriptor
programmed by the installer (see relay descriptor
programming section).
nn DEVICE IS OFF
HIT THE "*" KEY
Voice: "
voice descriptor
DEVICE nn ON/OFF. TO EXIT
ENTER 00 NOW"
From a keypad, press * to continue. The ENTER
DEVICE NO. prompt will appear.
From a telephone keypad, enter 00 to exit, or enter the
next relay number to be programmed. The current on/off
state of that relay will be annunciated as described
above. Alternatively, if 6 seconds elapses with no key
depression, the voice module will annunciate the
"ENTER DEVICE CODE NOW" message.
- VISTA-50P 1
- VISTA-50PUL 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 8
- HOW TO USE THIS MANUAL 9
- Polling Loop Expansion: 13
- Wireless Expansion: 13
- Wireless Expansion 13
- Device Programming Mode 14
- Common Lobby Logic 17
- DATA FIELD 17
- DESCRIPTIONS) 17
- COMMON LOBBY 19
- Figure 3 24
- Figure 4 24
- TRIGGERS 25
- Figure 5 25
- Figure 6 26
- POWER-UP PROCEDURE 27
- SPECIFICATIONS AND 32
- ACCESSORIES 32
- Figure 8 33
- IMPORTANT: 34
- Figure 10 38
- Figure 9 39
- FINAL POWER UP 39
- PROCEDURE 39
- Figure 11 39
- VOLTAGE TRIGGERS 41
- Figure 12 41
- Wire Gauge Max. Length 45
- #22 gauge 650 feet 45
- #20 gauge 950 feet 45
- #18 gauge 1500 feet 45
- #16 gauge 2400 feet 45
- FINAL POWER-UP PROCEDURE 46
- FINAL POWER UP PROCEDURE 47
- (5700/5800 series) 53
- Figure 15 55
- Device Programming 55
- Programming 56
- House ID 57
- Device Address 57
- PROGRAMMING WIRELESS ZONES 58
- Go/No Go Test Mode 67
- Transmitter ID Sniffer Mode 67
- Programming Options Defined 68
- Time Driven 68
- 4204 RELAY MODULE 69
- restores 71
- STOP (STP): 72
- SCHEDULING OPTIONS 74
- (VIP) MODULE 77
- VOICE MODULE 79
- #93 MENU MODE PROGRAMMING 80
- DEVICES 80
- Section 11 81
- Figure 19 82
- MODEL EAGLE SECURITY 83
- AUDIO ALARM VERIFICATION 84
- Figure 20 84
- 1 2 3 4 5 6 7 8 9 85
- J7 CONNECTOR 86
- 4142TR CABLE 86
- RELAY OUTPUTS AND POWERLINE 87
- CARRIER DEVICES 87
- Figure 23 89
- 2.8A maximum 91
- Figure 26 92
- Section 14: EVENT LOG OPTIONS 94
- SETTING THE REAL TIME CLOCK 95
- CLEAR EVENT LOG 97
- 0=NO 1=YES 97
- Figure 28 98
- Figure 29 98
- NO CONNECTION 99
- RED (+)BLK (–) 99
- THE MECHANICS OF PROGRAMMING 100
- Battery Calculation Worksheet 101
- 95 96 99 107
- 109
- 109
- 12345678 112
- 95 96 99 Duress 113
- 119
- ZONE PROGRAMMING 121
- PROGRAMMING 121
- ALPHA PROGRAMMING 121
- ZONE TYPE DEFINITIONS 121
- ∗) to exit back to normal 122
- CHARACTER (ASCII) CHART 129
- to exit Menu Mode 131
- * to accept entry 132
- Number (HH:MM) (HH:MM) 140
- Hol. Partition 143
- Mon/Day 1 2345678 143
- HOLIDAY NUMBER ? 143
- Action Codes: 146
- 01 RELAY GRP # ? 146
- GROUP ? 12345678 147
- ACCESS SCHED # ? 148
- MON A1 Window 1? 148
- MON A1 Window 2 ? 148
- 06 ENTER OUTPUT# 151
- 06 Days? MTWTFSS 152
- ], or [A] = 95;Duress = 92 154
- NOTES Note: Low Speed will 157
- Other brands are not 162
- Summary of Connections 165
- LOG PRINTER CONNECTIONS 165
- Auth Title 167
- Section 25: KEYPAD FUNCTIONS 173
- ENTER DEVICE NO 177
- REGULATORY AGENCY STATEMENTS 182
- IMPORTANT 188
- SET SWITCHES WITH 188
- BATTERY REMOVED 188
- SUMMARY OF SYSTEM COMMANDS 189
- SPECIFICATIONS 190
- CONTACTING TECHNICAL SUPPORT 191
- WARNING! 194
- N5945-6V2 2/98 195
- N5944-6V1 Rev B 4/99 196
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50
(132 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.698 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels