ADEMCO Vista-50 Manuel d'utilisateur Page 107
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
– 95 –
*15 KEYSWITCH ASSIGNMENT
Enter the partition number 1-8 in which the keyswitch is being used;
otherwise, enter 0.
Requires the use of zone 7 wired loop (zone 7 no longer available as
protection zone when used for keyswitch operation). If the keyswitch is
used, the fire and panic alarm voltage triggers automatically become
ARMING and READY status outputs for support of the Keyswitch LEDs.
Note: Zone type 10 is automatically assigned to zone 7 if a keyswitch is
used. Reports openings/closing by user "0" if reporting is enabled in field
*40.
*16 CONFIRMATION OF ARMING DING (partition-specific)
Enter 1 to enable 1/2 second external alarm sounding ("ding") at the end
of exit delay (or after kisoff from the central station, if sending closing
reports.) Otherwise enter 0.
*17 AC LOSS KEYPAD SOUNDING
Enter 1 to enable sounding at the keypad (rapid beeping) when AC
power is lost (sounding occurs about 2 minutes after actual AC loss).
Enter 0 if no AC power loss keypad sounding is desired.
*18 AC LOSS SIREN
Enter 1 to enable the external alarm sound after AC power has been out
for 4 hours; Otherwise enter 0 (no alarm). (Must be "1" for UL)
*19 RANDOMIZE AC LOSS REPORT
Selecting this option helps prevent an overload of AC loss messages at
the central station during a community blackout.
Enter 1 to randomize AC loss reporting between 10-40 min. after an
actual AC loss. Enter 0 for normal AC loss reporting (about 2 minutes
after actual AC loss).
*20 VIP MODULE PHONE CODE
If a 4285 voice module is being used, enter the 2-digit phone code used
to access the system.
Enter 01-09 for first digit, and enter 11 (for *) or 12 (for #) for second digit.
To disable the voice module, enter 00 for the 1st digit and enter 11 for
the 2nd digit of the code (disable code = 00,11).
*21 PREVENT FIRE TIME-OUT
Enter 1 to disable (no timeout) the alarm sounder duration for any zone
designated as a fire zone, regardless of partition, so that fire sounding
continues until the system is reset.
Enter 0 if the normal burglary alarm sounder duration (programmed in
partition-specific field *13) should apply to fire alarms.
*22 KEYPAD PANIC ENABLES (partition-specific) | |
Enter 1 to enable the appropriate keypad panics used 95 96 99
in this partition. Otherwise enter 0.
- VISTA-50P 1
- VISTA-50PUL 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 8
- HOW TO USE THIS MANUAL 9
- Polling Loop Expansion: 13
- Wireless Expansion: 13
- Wireless Expansion 13
- Device Programming Mode 14
- Common Lobby Logic 17
- DATA FIELD 17
- DESCRIPTIONS) 17
- COMMON LOBBY 19
- Figure 3 24
- Figure 4 24
- TRIGGERS 25
- Figure 5 25
- Figure 6 26
- POWER-UP PROCEDURE 27
- SPECIFICATIONS AND 32
- ACCESSORIES 32
- Figure 8 33
- IMPORTANT: 34
- Figure 10 38
- Figure 9 39
- FINAL POWER UP 39
- PROCEDURE 39
- Figure 11 39
- VOLTAGE TRIGGERS 41
- Figure 12 41
- Wire Gauge Max. Length 45
- #22 gauge 650 feet 45
- #20 gauge 950 feet 45
- #18 gauge 1500 feet 45
- #16 gauge 2400 feet 45
- FINAL POWER-UP PROCEDURE 46
- FINAL POWER UP PROCEDURE 47
- (5700/5800 series) 53
- Figure 15 55
- Device Programming 55
- Programming 56
- House ID 57
- Device Address 57
- PROGRAMMING WIRELESS ZONES 58
- Go/No Go Test Mode 67
- Transmitter ID Sniffer Mode 67
- Programming Options Defined 68
- Time Driven 68
- 4204 RELAY MODULE 69
- restores 71
- STOP (STP): 72
- SCHEDULING OPTIONS 74
- (VIP) MODULE 77
- VOICE MODULE 79
- #93 MENU MODE PROGRAMMING 80
- DEVICES 80
- Section 11 81
- Figure 19 82
- MODEL EAGLE SECURITY 83
- AUDIO ALARM VERIFICATION 84
- Figure 20 84
- 1 2 3 4 5 6 7 8 9 85
- J7 CONNECTOR 86
- 4142TR CABLE 86
- RELAY OUTPUTS AND POWERLINE 87
- CARRIER DEVICES 87
- Figure 23 89
- 2.8A maximum 91
- Figure 26 92
- Section 14: EVENT LOG OPTIONS 94
- SETTING THE REAL TIME CLOCK 95
- CLEAR EVENT LOG 97
- 0=NO 1=YES 97
- Figure 28 98
- Figure 29 98
- NO CONNECTION 99
- RED (+)BLK (–) 99
- THE MECHANICS OF PROGRAMMING 100
- Battery Calculation Worksheet 101
- 95 96 99 107
- 109
- 109
- 12345678 112
- 95 96 99 Duress 113
- 119
- ZONE PROGRAMMING 121
- PROGRAMMING 121
- ALPHA PROGRAMMING 121
- ZONE TYPE DEFINITIONS 121
- ∗) to exit back to normal 122
- CHARACTER (ASCII) CHART 129
- to exit Menu Mode 131
- * to accept entry 132
- Number (HH:MM) (HH:MM) 140
- Hol. Partition 143
- Mon/Day 1 2345678 143
- HOLIDAY NUMBER ? 143
- Action Codes: 146
- 01 RELAY GRP # ? 146
- GROUP ? 12345678 147
- ACCESS SCHED # ? 148
- MON A1 Window 1? 148
- MON A1 Window 2 ? 148
- 06 ENTER OUTPUT# 151
- 06 Days? MTWTFSS 152
- ], or [A] = 95;Duress = 92 154
- NOTES Note: Low Speed will 157
- Other brands are not 162
- Summary of Connections 165
- LOG PRINTER CONNECTIONS 165
- Auth Title 167
- Section 25: KEYPAD FUNCTIONS 173
- ENTER DEVICE NO 177
- REGULATORY AGENCY STATEMENTS 182
- IMPORTANT 188
- SET SWITCHES WITH 188
- BATTERY REMOVED 188
- SUMMARY OF SYSTEM COMMANDS 189
- SPECIFICATIONS 190
- CONTACTING TECHNICAL SUPPORT 191
- WARNING! 194
- N5945-6V2 2/98 195
- N5944-6V1 Rev B 4/99 196
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50
(132 pages)© 2020, manymanuals.fr. Tous droits réservés | 3.695 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels