ADEMCO Vista-50 Manuel d'utilisateur Page 74
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
–62–
Relay Group
Relays may be grouped for common activation by
time driven events (commands 06-10--see Section
20:
SCHEDULING OPTIONS
for more information).
Enter 0 (no group) or 1-8 for a specific group
number. Press * to continue.
Restriction
1=yes 0=no
The system may have some devices which are not
intended to be under end user control, such as
relays activating fire doors or machinery. Enter 1 if
the end user will be restricted from accessing this
relay. Press * to continue.
Relay Type
Enter 1 for 4204 relay outputs. Enter 2 for Powerline
Carrier devices. Press * to continue.
ECP ADDRESS
For relay module (4204) outputs, enter the actual
relay module's address (01-15) as set by its DIP
switches.
MODULE RELAY #
For 4204 relay outputs, enter the specific relay
number on that module (1-4). Press * to continue.
House Code
For Powerline Carrier devices, enter the numerical
equivalent of the House Code of the device as
follows:
A=00 E=04 I=08 M=12
B=01 F=05 J=09 N=13
C=02 G=06 K=10 O=14
D=03 H=07 L=11 P=15
Unit Code
Enter the numberical unit code of the Powerline
Carrier device (00-15). Press * to continue.
The keypad will display the Start and Stop summary
screens again. Press * to continue.
5. When all relays have been programmed, enter 00 at the "ENTER RELAY NO."
prompt.
6. If defining a Zone List, continue to the next procedure in this section. If not,
enter 00 + * at the next two prompts. Then enter *99 to exit programming
completely. After exiting, enter the [Installer Code] + OFF to cancel the
system's settling delay.
- VISTA-50P 1
- VISTA-50PUL 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 8
- HOW TO USE THIS MANUAL 9
- Polling Loop Expansion: 13
- Wireless Expansion: 13
- Wireless Expansion 13
- Device Programming Mode 14
- Common Lobby Logic 17
- DATA FIELD 17
- DESCRIPTIONS) 17
- COMMON LOBBY 19
- Figure 3 24
- Figure 4 24
- TRIGGERS 25
- Figure 5 25
- Figure 6 26
- POWER-UP PROCEDURE 27
- SPECIFICATIONS AND 32
- ACCESSORIES 32
- Figure 8 33
- IMPORTANT: 34
- Figure 10 38
- Figure 9 39
- FINAL POWER UP 39
- PROCEDURE 39
- Figure 11 39
- VOLTAGE TRIGGERS 41
- Figure 12 41
- Wire Gauge Max. Length 45
- #22 gauge 650 feet 45
- #20 gauge 950 feet 45
- #18 gauge 1500 feet 45
- #16 gauge 2400 feet 45
- FINAL POWER-UP PROCEDURE 46
- FINAL POWER UP PROCEDURE 47
- (5700/5800 series) 53
- Figure 15 55
- Device Programming 55
- Programming 56
- House ID 57
- Device Address 57
- PROGRAMMING WIRELESS ZONES 58
- Go/No Go Test Mode 67
- Transmitter ID Sniffer Mode 67
- Programming Options Defined 68
- Time Driven 68
- 4204 RELAY MODULE 69
- restores 71
- STOP (STP): 72
- SCHEDULING OPTIONS 74
- (VIP) MODULE 77
- VOICE MODULE 79
- #93 MENU MODE PROGRAMMING 80
- DEVICES 80
- Section 11 81
- Figure 19 82
- MODEL EAGLE SECURITY 83
- AUDIO ALARM VERIFICATION 84
- Figure 20 84
- 1 2 3 4 5 6 7 8 9 85
- J7 CONNECTOR 86
- 4142TR CABLE 86
- RELAY OUTPUTS AND POWERLINE 87
- CARRIER DEVICES 87
- Figure 23 89
- 2.8A maximum 91
- Figure 26 92
- Section 14: EVENT LOG OPTIONS 94
- SETTING THE REAL TIME CLOCK 95
- CLEAR EVENT LOG 97
- 0=NO 1=YES 97
- Figure 28 98
- Figure 29 98
- NO CONNECTION 99
- RED (+)BLK (–) 99
- THE MECHANICS OF PROGRAMMING 100
- Battery Calculation Worksheet 101
- 95 96 99 107
- 109
- 109
- 12345678 112
- 95 96 99 Duress 113
- 119
- ZONE PROGRAMMING 121
- PROGRAMMING 121
- ALPHA PROGRAMMING 121
- ZONE TYPE DEFINITIONS 121
- ∗) to exit back to normal 122
- CHARACTER (ASCII) CHART 129
- to exit Menu Mode 131
- * to accept entry 132
- Number (HH:MM) (HH:MM) 140
- Hol. Partition 143
- Mon/Day 1 2345678 143
- HOLIDAY NUMBER ? 143
- Action Codes: 146
- 01 RELAY GRP # ? 146
- GROUP ? 12345678 147
- ACCESS SCHED # ? 148
- MON A1 Window 1? 148
- MON A1 Window 2 ? 148
- 06 ENTER OUTPUT# 151
- 06 Days? MTWTFSS 152
- ], or [A] = 95;Duress = 92 154
- NOTES Note: Low Speed will 157
- Other brands are not 162
- Summary of Connections 165
- LOG PRINTER CONNECTIONS 165
- Auth Title 167
- Section 25: KEYPAD FUNCTIONS 173
- ENTER DEVICE NO 177
- REGULATORY AGENCY STATEMENTS 182
- IMPORTANT 188
- SET SWITCHES WITH 188
- BATTERY REMOVED 188
- SUMMARY OF SYSTEM COMMANDS 189
- SPECIFICATIONS 190
- CONTACTING TECHNICAL SUPPORT 191
- WARNING! 194
- N5945-6V2 2/98 195
- N5944-6V1 Rev B 4/99 196
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50
(132 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels