ADEMCO Vista-50 Guide d'installation Page 69
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 6 – Scheduling Options
6-5
PROMPT
EXPLANATION
Timed Events ?
1 = YES 0 = NO 0
Enter 1 to program timed events for relay outputs, additional schedules, and other system functions. Refer
to
Time-Driven Event Programming
later in this section for detailed procedures.
Enter 0 to move to the “Access Sched?” prompt.
Access Sched. ?
1 = YES 0 = NO 0
Enter 1 to program access schedules. Refer to
Limitation of
Access Schedules Programming
later in this
section for detailed procedures.
Enter 0 to move to the “Quit?” prompt.
Quit ?
1 = YES 0 = NO 0
Enter 1 to quit
#80 Scheduling Menu Mode
and return to normal operating mode.
Enter 0 to make any changes or review the scheduling programming options. If you press 0, the “Time
Window?” prompt is displayed.
Time Windows
The system provides 20 time windows that are defined
with start and stop times. These windows are used for
various open/close and access schedules, as well as for
output controls, and are the basis of the scheduling
system. These windows are shared among all 8
partitions.
Time Windows Worksheet
The following worksheet is an example of the worksheet
found in the Programming Guide. This worksheet will
help you define time windows and scheduling aspects of
this system before you program them. Note that time
windows can span midnight; for example, from 11 PM
to 1 AM.
Time Window
Number
Start Time
(HH:MM)
Stop Time
(HH:MM)
1
2
3…..20
A time window must have a start and a stop time.
Time Windows Programming
Enter Scheduling Mode by entering Installer Code +
[#] + [80]. The keypad displays the Time Window
Programming prompt.
PROMPT
EXPLANATION
Time Window ?
1 = YES 0 = NO 0
Enter 1 at this main menu prompt to program time windows.
Time Window # ?
01-20, 00 = Quit 01
Enter the 2-digit time window number (01-20) to be programmed.
Press [✳] to accept the entry. Enter 00 + [✳] at the “Time Window #?” prompt to quit time window
programming and display the “Quit ?” prompt.
01 TIME WINDOW
00:00AM 00:00AM
If you entered a time window number, the cursor is now positioned on the tens of hours digit of the start of
window entry.
Enter the desired start of window hour and press [✳]. The cursor moves to the minutes position. Enter the
desired minutes and press [✳]. Toggle the AM/PM indication by pressing any key 0-9 while the cursor is
under the A/P position and then press [✳]. Repeat this to program the stop of window entry.
When the entry is completed, the “Time Window #?” prompt is displayed again.
Enter the next time window number to be programmed and repeat the procedure.
Quit ?
1 = YES 0 = NO 0
Enter 0 at the Quit ? prompt to return to the main menu choices and continue programming.
Enter 1 to quit Scheduling Menu Mode.
Because the time windows are shared among all partitions, it is important to make sure that changing a
time window does not adversely affect desired actions in other partitions.
- Table of Contents 3
- List of Figures 5
- General Description 7
- Partitioning 9
- OFFICE 1 OFFICE 2 10
- MAIN ENTRANCE 10
- COMMON LOBBY 10
- V128BP-001-V0 10
- B = Bypassed/Ready 11
- = Alarm/Trouble 11
- Installing the Control 13
- Installing the Keypads 15
- Installing External Sounders 16
- ALARM SOUNDER OUTPUT: 17
- 1-VDC - 13.8VDC 17
- 1.7A MAXIMUM 17
- Telephone Line Connections 18
- ZONE 1,8: 100 OHMS MAXIMUM 19
- Figure 3-11 20
- 333PRM-001-V0 21
- 333PRM-003-V0 22
- Installing RPM Devices 23
- GAUGE LENGTH 24
- #22 650 FT 24
- #20 950 FT 24
- #18 1500 FT 24
- #16 2400 FT 24
- Wireless Zone Expansion 25
- 5881ENHC-001-V0 26
- Device Programming 27
- Menu Mode 27
- Installing Output Devices 29
- 123456789 30
- Remote Keypad Sounder 31
- Installing a 4100SM 32
- #93 Menu Mode 33
- Figure 3-29 34
- CONTROL PANEL 35
- Connecting the Transformer 36
- Programming 41
- #93 Menu Mode Programming 42
- Zone Number Designations 44
- Section 4 – Programming 45
- Polling Loop Supervision 46
- SECTION 3 46
- Programming for 4100SM 47
- Data Field Descriptions 49
- Support 56
- Scheduling Options 65
- Time Window Definitions 66
- Windows Programming 68
- Holiday Schedule Programming 68
- Time-Driven Event Programming 69
- Limitation of 69
- Access Schedules Programming 69
- #80 Scheduling Menu Mode 69
- Daily Open/Close Schedules 70
- Holiday Schedules 70
- Time-Driven Events 71
- EXPLANATION 73
- Temporary Schedules 75
- User Scheduling Menu Mode 76
- Downloading Primer 79
- On-Line Control Functions 80
- Direct-Wire Downloading 81
- Telco Handoff 81
- Setting the Real-Time Clock 83
- User Access Codes 85
- Multiple Partition Access 86
- Exiting the User Edit Mode 88
- Testing the System 89
- Trouble Conditions 91
- To the Installer 91
- Contacting Technical Support 92
- Regulatory Agency Statements 93
- Requirements 94
- Summary of System Commands 97
- Specifications 99
- Contact ID Event Codes 101
- Index-1 103
- Index-4 106
- WARNING! 108
- LIMITED WARRANTY 109
- N5944-6V2 5/04 Rev A 112
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50
(234 pages)
(56 pages)
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels