ADEMCO Vista-50 Guide d'installation Page 26
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
VISTA-50P/VISTA-50PUL Installation and Setup Guide
3-14
RF System Installation Advisories
• Place the receiver in a high, centrally located area.
Do not place it on or near metal objects. This will
decrease the range and/or block transmissions.
• Install the RF receiver at least 10 feet from the
control panel or any keypads, to avoid interference
from the microprocessors in these units.
• If dual receivers are used:
a. They must be at least 10 feet from each other,
as well as from the control panel and remote
keypads.
b. Each receiver must be set to a different device
address. The receiver set to the lower address
is considered the 1st RF receiver for
supervisory purposes.
c. The House IDs must be the same.
d. Using two receivers does not increase the
number of transmitters the system can support
(85 zones using the 5881H, plus a wireless
keypad).
Installation and Setup of the 5881 RF Receivers
Take note of the address you select for the RF
receiver, as this address must be enabled in
the system’s
Device Programming
in the
#93
Menu Mode
.
5881ENHC-001-V0
SCREW
Figure 3-19: Installing the 5881ENHC with Tamper
Protection
To install the 5881 RF receiver, perform the following
steps:
Step Action
1 Mount the receiver, following the advisories
stated previously.
2 Set the DIP switches in the receiver for the
address (01-07). See Figure 3-20.
Make sure the address setting is not
being used by another device (keypad,
relay module, etc.).
3 If installing a 5881ENHC, install a flat-head
screw (supplied) in the case tamper tab as
shown in Figure 3-19. When the receiver is
pried from the wall, the tamper tab will break
off and remain on the wall. This will activate
a tamper switch in the receiver and cause
generation of a tamper signal. Note that this
signal will also be generated when the
receiver’s front cover is removed.
4 Connect the receiver’s wire harness to the
keypad terminals (6, 7, 8, and 9). Plug the
connector at the other end of the harness into
the receiver.
5 Refer to the Installation Instructions
provided with the receiver for installations
regarding antenna mounting, etc.
- Table of Contents 3
- List of Figures 5
- General Description 7
- Partitioning 9
- OFFICE 1 OFFICE 2 10
- MAIN ENTRANCE 10
- COMMON LOBBY 10
- V128BP-001-V0 10
- B = Bypassed/Ready 11
- = Alarm/Trouble 11
- Installing the Control 13
- Installing the Keypads 15
- Installing External Sounders 16
- ALARM SOUNDER OUTPUT: 17
- 1-VDC - 13.8VDC 17
- 1.7A MAXIMUM 17
- Telephone Line Connections 18
- ZONE 1,8: 100 OHMS MAXIMUM 19
- Figure 3-11 20
- 333PRM-001-V0 21
- 333PRM-003-V0 22
- Installing RPM Devices 23
- GAUGE LENGTH 24
- #22 650 FT 24
- #20 950 FT 24
- #18 1500 FT 24
- #16 2400 FT 24
- Wireless Zone Expansion 25
- 5881ENHC-001-V0 26
- Device Programming 27
- Menu Mode 27
- Installing Output Devices 29
- 123456789 30
- Remote Keypad Sounder 31
- Installing a 4100SM 32
- #93 Menu Mode 33
- Figure 3-29 34
- CONTROL PANEL 35
- Connecting the Transformer 36
- Programming 41
- #93 Menu Mode Programming 42
- Zone Number Designations 44
- Section 4 – Programming 45
- Polling Loop Supervision 46
- SECTION 3 46
- Programming for 4100SM 47
- Data Field Descriptions 49
- Support 56
- Scheduling Options 65
- Time Window Definitions 66
- Windows Programming 68
- Holiday Schedule Programming 68
- Time-Driven Event Programming 69
- Limitation of 69
- Access Schedules Programming 69
- #80 Scheduling Menu Mode 69
- Daily Open/Close Schedules 70
- Holiday Schedules 70
- Time-Driven Events 71
- EXPLANATION 73
- Temporary Schedules 75
- User Scheduling Menu Mode 76
- Downloading Primer 79
- On-Line Control Functions 80
- Direct-Wire Downloading 81
- Telco Handoff 81
- Setting the Real-Time Clock 83
- User Access Codes 85
- Multiple Partition Access 86
- Exiting the User Edit Mode 88
- Testing the System 89
- Trouble Conditions 91
- To the Installer 91
- Contacting Technical Support 92
- Regulatory Agency Statements 93
- Requirements 94
- Summary of System Commands 97
- Specifications 99
- Contact ID Event Codes 101
- Index-1 103
- Index-4 106
- WARNING! 108
- LIMITED WARRANTY 109
- N5944-6V2 5/04 Rev A 112
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50
(234 pages)
(56 pages)
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.313 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels