ADEMCO Vista-50 Guide d'installation télécharger pdf (Page 41)

4-1

SECTION 4

Programming

•••••••••••••••••••••••••••••••••••••••••••••••••

Program Modes

There are two programming modes for the VISTA-

50P/VISTA-50PUL. These are the Data Field Program

Mode and the #93 Menu Mode. The Data Field Program

Mode is where many system options are programmed.

The #93 Menu Mode is an interactive mode that

requires a 2-line alpha keypad (6139/6160).

The factory-loaded defaults (✳97) enable

keypad addresses 00-01 only. A keypad set to

one of these addresses must be used to

program the system initially.

Local keypad programming can be disabled

throu

h Compass downloadin

software. If this

is done, Program mode can only be accessed

via the downloading software.

Entering and Exiting Programming Mode

Enter Programming mode using either method a or b:

a. Press both the [✳] and [#] keys at the same time

within 30 seconds after power is applied to the

control.

b. Enter the Installer Code + [8] + [0] + [0] keys.

The factory installer code can be changed once in

the Program mode (field ✳00).

NOTE: The default for the Installer Code is 4140.

Exit the Programming mode by either method a or b:

a. Press [✳] + [9] + [8]. Exiting by this method

prevents the installer code from being used to re-

enter Programming mode. Only method “a” can be

used to re-enter Programming mode.

b. Press [✳] + [9] + [9]. Exiting by this method

permits the installer code to be being used to re-

enter Programming mode.

Data Field Programming Mode

In the Data Field Program Mode you may access any

field simply by entering either [✳] or [#] + the field

number:

• To write or change information in a field press [✳]

+ the field number (✳03).

• To read the information in a field press [#] + the

field number (#03).

When the entries for a field are completed, the keypad

beeps three times and advances to the next field.

Summary of Data Field Programming Commands

✳91

Select partition for programming partition-specific fields

✳92

Display the software revision level of the control panel

✳93

Enter Menu mode programming

✳94

Go to next page of fields

✳99

Go back to previous page of fields or exit

Programming Mode with no installer code lockout

✳98

Exit Programming Mode with Installer Code lockout

Moving Between Programming Levels

The data fields are grouped into three levels (referred to

as “pages”). The first page is accessed as soon as

Programming Mode is entered.

The second and third pages of data fields are indicated

at the keypad by a 1 and 2, respectively, in front of the

2-digit field address. “ALT PROGRAM MODE” is

displayed along with a “100” or “200,” indicating which

page of program fields is accessed.

To access the next level of programming fields, perform

the following steps:

Step Action

Press ✳94.

2 Press [✴] + [XX], where XX = the last two

digits of the program field, and make the

desired entry.

NOTES:

Press ✳94 to move to 2nd page, (fields 1✳01 - 1✳76);

press ✳99 to move back to 1st page.

Press ✳94 to move to 3rd page (fields 2✳00 - 2✳21);

press ✳99 to move back to 2nd page

Entry Errors

• If an address is improperly entered, the keypad

displays “FC.”

• If a program entry is improperly entered (for

example, a larger number than is permitted), the

keypad display will go blank.

In either of the above cases, simply re-enter [✳] + the

correct field number and then enter the correct data.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 111 112

Commentaires sur ces manuels

Pas de commentaire

ADEMCO Vista-50 Guide d'installation Page 41

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO Vista-50