ADEMCO VISTA-250FBP Guide d'installation Page 86
- Page / 136
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
VISTA-128FBP/VISTA-250FBP Installation and Setup Guide
6-6
Daily Open/Close Schedules
Each partition can be assigned one daily open/close
schedule, plus a holiday schedule. Temporary
schedules are programmed separately, using the #81
Temporary Schedule Menu Mode. To program
additional open/close schedules, see Time-Driven Events
Programming later in this section for the procedure.
Open/Close Schedule Worksheet
The following worksheet is an example of the worksheet
found in the Programming Guide. Write the previously
defined time window numbers for open and close for
each partition.
Part Mon Tues Wed Thur Fri Sat Sun Hol
Op Cl Op Cl Op Cl Op Cl Op Cl Op Cl Op Cl Op Cl
1
2
3…8
Open/Close Schedule Programming
After entering Scheduling Menu Mode, press [0] until the “O/C Schedules?” prompt appears.
PROMPT
EXPLANATION
O/C Schedules ?
1 = YES 0 = NO 0
Enter 1 to program opening and closing schedules.
Partition # ?
01-08, 00 = Quit 01
Enter the appropriate partition number for which the following open/close schedules will apply.
Enter 00 + [✳] at the “Partition #?” prompt to quit open/close schedules programming and display the “Quit
?” prompt.
Mon P1 OP WIND.?
00:00 00:00 00
Enter the time window number 01-20 for the displayed day’s opening schedule beginning with Monday.
Enter 00 if no schedule is desired for a particular day. As the number is keyed in, the actual time that has
been stored for that window number is displayed as a programming aid.
Press [✳] to accept the entry.
Mon P1 CL WIND.?
00:00 00:00 00
Enter the time window number for the displayed day’s closing schedule. As the number is keyed in, the
actual time that has been stored for the window number is displayed.
Press the [✳] key to accept the entry.
Tue P1 OP WIND.?
00:00 00:00 00
The keypad now prompts for Tuesday’s open/close schedule. Follow the procedure for Monday’s prompts.
When the last day of the week has been programmed, the holiday opening and closing window prompts are
displayed.
Hol P1 OP WIND.?
00:00 00:00 00
Repeat the procedure for the holiday opening and closing time windows.
Press the [✳] key to accept the entry.
When the entries are completed, the “Partition #?” prompt is displayed again. Repeat this procedure for
each partition in the system.
Quit ?
1 = YES 0 = NO 0
Enter 0 at the “Quit ?” prompt to return to the main menu choices and continue programming.
Enter 1 to quit Scheduling Menu Mode.
Holiday Schedules
A holiday schedule overrides the regular daily open/close schedule on the programmed holidays throughout the year.
The system provides up to 16 holidays that can be assigned for the system. Each holiday can be assigned to any
combination of partitions. List the desired holidays in a Month/Day format on the worksheet. Check the partitions for
which these holidays apply.
- K0376V2 7/09 Rev. B 1
- Table of Contents 3
- List of Figures 6
- PRODUCT MODEL NUMBERS: 7
- General Requirements 9
- COMMUNICATIONS 12
- General Description 15
- YELLOW DATA 18
- GREEN DATA 18
- Partitioning 19
- COMMON LOBBY 20
- Installing the Control 23
- Commercial Fire Guidelines 24
- Installing the Keypads 25
- Device Programming 26
- #93 Menu 26
- Auxiliary Relay Connections 30
- Telephone Line Connections 31
- Main Dialer Connections 31
- 2000 OHMS 34
- Figure 3-11 35
- Zone Programming 37
- VPLEX-VSI 39
- Wireless Zone Expansion 40
- Programming 41
- #93 Menu Mode 41
- 5881-001-V0 42
- SWITCH (N.O.) 46
- Event Log Connections 48
- Connecting the Transformer 48
- Earth Ground Connections 49
- Battery 52
- BATTERY TABS 53
- MAIN PCB 53
- #93 Menu Mode Programming 56
- Section 4 – Programming 57
- MAIN MENU 57
- OPTIONS 57
- Zone Number Designations 58
- Polling Loop Supervision 61
- SECTION 3: 61
- Zone Input Type Definitions 62
- Programming for Communicator 63
- Programming Guide 65
- Report Code Programming 67
- Output Programming 75
- ✳16 for Waterflow and 78
- Scheduling Options 81
- Time Window Definitions 82
- Limitation of 85
- Access Schedules Programming 85
- #80 Scheduling Menu Mode 85
- Daily Open/Close Schedules 86
- Holiday Schedules 86
- Time-Driven Events 87
- 30=Auto bypass – Zone list 90
- 31=Auto unbypass – Zone list 90
- 42=Enable Access Window for 90
- Access group(s) 90
- 50=Off-Normal Reminder 90
- 1 91
- 2 91
- 3…8 91
- Temporary Schedules 92
- User Scheduling Menu Mode 94
- Downloading Primer 95
- Section 7 – Downloading 97
- Figure 7-1 98
- Setting the Real-Time Clock 99
- User Access Codes 101
- User 3 User 3 102
- Level 1 Level 4 102
- Master Oper B 102
- EXPLANATION 103
- Exiting the User Edit Mode 104
- Testing the System 105
- Burglary Walk-Test ( 106
- Armed Burglary System Test 107
- Trouble Conditions 108
- To the Installer 109
- Regulatory Agency Statements 111
- FCC PART 68 NOTICE 113
- Summary of System Commands 115
- Specifications 117
- Contact ID Codes 119
- Event Log Alpha Descriptors 120
- 4-3, 4-4 124
- 6-4, 6-2 125
- 6-4, 6-5 127
- WARNING: 135
- ÊK0376V2Š 136
- ÊK0376V2ŠÊK0376V2Š 136
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO VISTA-250FBP
(54 pages)
(64 pages)Seametrics WMP-Series manuali
Manuali dei proprietari e guide per l'utente per Apparecchiature Seametrics WMP-Series.
We fornisce 1 manuali pdf Seametrics WMP-Series per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels