ADEMCO VISTA-128B Manuel d'utilisateur télécharger pdf

ELAN Home Systems ● 1690 Corporate Circle ● Petaluma, CA 94954 USA

tech support: 800.622.3526 • main: 760.710.0990 • sales: 877.289.3526 • email: [email protected]

Integration Note

Manufacturer: Ademco, First Alert

Model Number(s): VISTA–128BP, VISTA–250BP, FA1660C

Core Module Versions:

3.0 or above

Comments:

Document Revision Date: 8/6/2013

OVERVIEW AND SUPPORTED FEATURES

The Ademco Vista 128BP, 250BP and the First Alert FA1660C are security panels that integrate with

the g! system using an RS-232 serial connection. The panel requires the model 4100 SM serial interface

module to enable the RS-232 communication between the g! system controller and the control panel.

Integration of the security system provides monitoring and control from any touch screen, telephone or

computer both locally and remotely. Additionally, events occurring in the security system can trigger

system commands in other sub-systems in the home. For example, a burglar alarm can turn all the lights

on and send out email alerts.

IMPORTANT! This document applies to the Ademco/First Alert 128/250BP/FA1660C panels, and does

not apply to the BPE panels. The 128BPE (and variants) are NOT SUPPORTED. In some cases it may

not be clear from hardware/packaging that the 128BP is in fact a 128BPE, as the difference is primarily

firmware. a 4.x firmware version is BPE, a 3.x or earlier firmware is BP. To tell if you have a BPE panel,

enter programming mode ([Installer Code] + [8000]) AND go to field *92; you will have two lines of info -

087

2nd line -03 indicates V3.xx, if – 04 = V4 chip.

(If field 1*78 says not used and 3* is not there then it’s a V3.xx.)

******The BPE (4.x) firmware requires a different protocol and wiring and is not supported!******

HESE PANELS SUPPORT THE FOLLOWING FEATURES:

Arm – Disarm: Arm and disarm from the Viewer interface is supported for partition number 1 only. Status

information is available for all partitions.

Zone Status: Zone status information is available for all zones (in any partition), and is properly shown in

the Viewer. See exceptions below.

History View: The history view is properly supported on any Viewer.

Auto Zone and Partition Detection: After a zone has been faulted the g! system will automatically

detect the zone number, partition number and zone name.

HESE PANELS DO NOT SUPPORT THE FOLLOWING FEATURES:

Zone Bypass: Zones cannot be bypassed from the g! interface, only from the Ademco or First Alert

keypads. In the Ademco panel zones can be configured to automatically bypass if they are faulted when

arming the panel. Using this feature works well to overcome this limitation.

Multiple Partition Arm / Disarm: Only partition number 1 can be armed or disarmed from the g! user

interface, due to a limitation in the Ademco protocol and panel.

Auto Arm: Arming as a System Command from the Event Mapper is not supported with this panel.

1 2 3 4 5 6

Résumé du contenu

Page 1 - Integration Note

ELAN Home Systems ● 1690 Corporate Circle ● Petaluma, CA 94954 USA tech support: 800.622.3526 • main: 760.710.0990 • sales: 877.289.3526 • email: elan

Page 2 - INSTALLATION OVERVIEW

2 of 6 Zone Status: Zone status information for entry and exit zones is not communicated to g! during entry and exit delays. Entry/Exit Delay: This pa

Page 3 - CONNECTION METHODS

3 of 6 CONNECTION METHODS BILL OF MATERIALS # Device Manufacturer Part Number Protocol Connector Type Notes1 Co ntro l Panel Ademco /First A lert 12

Page 4 - PANEL PROGRAMMING

4 of 6 PANEL PROGRAMMING Before communication can start between the g! system and the Ademco or First Alert panels there are several fields that need

Page 5 - CONFIGURATION DETAILS

5 of 6 g! CONFIGURATION DETAILS The following table provides settings used in the g! Configurator when connecting to the Ademco / First Alert panel.

Page 6 - COMMON MISTAKES

6 of 6 COMMON MISTAKES 1. Failing to test the Cat5 cable assembly. It is easy to make a mistake when terminating the Cat5 cable with the RJ-45 connec

Plus de documents pour Systèmes de contrôle d'accès de sécurité ADEMCO VISTA-128B

Voir le document ADEMCO VISTA-128B Guide d'installation

ADEMCO VISTA-128B Guide d'installation (252 pages)

Voir le document ADEMCO VISTA-128B Guide de l'utilisateur

ADEMCO VISTA-128B Guide de l'utilisateur (80 pages)

Commentaires sur ces manuels

Pas de commentaire

ADEMCO VISTA-128B Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Systèmes de contrôle d'accès de sécurité ADEMCO VISTA-128B. Integration Note - ELAN Home Systems Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Systèmes de contrôle d'accès de sécurité ADEMCO VISTA-128B

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO VISTA-128B