ADEMCO LYNXR Guide d'installation télécharger pdf

K14117 3/06 Rev. A

ADEMCO LYNXR-I

Security Systems

Quick Start Guide

LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N

LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.

Introduction

This Quick Start Guide can help you install the rechargeable LYNXR-I quickly and easily by providing the basic

steps for installation using the built-in defaults. For more detailed information and important notes, refer to the

LYNXR-I Installation and Setup Guide.

The following steps assume that one of the system’s default tables will be used.

For programming data values and Powerline Carrier Devices other than those listed in the default tables, see the

Installation Instructions.

Default Table Summary

Zone Table 1 Table 2 Table 3 Table 4

2 front door front door front door front door

3 back door back door back door back door

4 window garage door window window

5 motion detector motion detector window window

6 ------- smoke detector window window

7 ------- ------- window window

8 ------- ------- motion detector motion detector

9 ------- ------- smoke detector smoke detector

26 loop 3 arm away loop 3 arm away loop 3 arm away loop 3 arm away

27 loop 2 disarm loop 2 disarm loop 2 disarm loop 2 disarm

28 loop 4 arm stay loop 4 arm stay loop 4 close device loop 4 close device

29 loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response

30 loop 3 arm away loop 3 arm away loop 3 arm away loop 3 arm away

31 loop 2 disarm loop 2 disarm loop 2 disarm loop 2 disarm

32 loop 4 arm stay loop 4 arm stay loop 4 close device loop 4 close device

33 loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response loop 1 no alarm response

92 duress duress duress duress

99 silent alarm audible alarm silent alarm silent alarm

Master User Code 1-2-3-4 1-2-3-4 1-2-3-4 1-2-3-4

Installer Code 4-1-1-2 4-1-1-2 4-1-1-2 4-1-1-2

Duress Code ------ ------ ------ ------

Entering Expert Program Mode: installer code + 8 0 0

Interactive Mode Used to Program

56 Enhanced Zone Programming Zone characteristics, report codes, and serial numbers

83 Enhanced Sequential Mode 5800 Series transmitter serial numbers

*84 Assign Zone Voice Descriptors Voice descriptors for each zone

Exiting Program Mode:

98 inhibits re-entry into the Programming mode using the Installer Code.

99 allows re-entry into the Program mode using Installer Code + 8 0 0.

NOTES: • Table 4 supports the automatic paging feature (open/close events reported to pager phone number),and a Powerline Carrier Device programmed

as device 8, which closes and stays closed upon burglary alarms and restores after bell timeout. For other applications or actions (e.g., using a

pulsing siren), see the *80 Device Programming Menu Mode section of the Installation Instructions.

• Primary and secondary report format for all tables is Ademco’s Contact ID® reporting.

• Tables 1, 3 and 4 record only alarms, alarm restores, troubles, and trouble restores in the event log. Table 2 records all events in the event log.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Security Systems

K14117 3/06 Rev. A ADEMCO LYNXR-I Security Systems Quick Start Guide UUUULLLL LYNXR-I is not intended for UL985 Household Fire applicatio

Page 2 - Installing LYNXR-I

Installing LYNXR-I Installation and Electrical Connections Step Action 1. Install the control as follows: a. Separate the front assembly from the

Page 3 - System Programming

INCOMINGPHONELINETOHANDSETPHONELINEWARNING:TO PREVENTRISK OF SHOCKDISCONNECTTELEPHONE LINEAT TELECOMJACK BEFORESERVICINGTHIS UNIT.WEEKLY TESTING ISRE

Page 4

Step Action 3. Enhanced Sequential Mode - Press *83, then follow the prompts as follows: A 01 a. Zone Number - Enter 2-digit zone n

Page 5 - 01009-012-V4

Step Action 3. (Cont.) 3) Once all 7 digits have been entered, press the [*] key. If less than 7 digits are entered, the keypad will emit a single

Page 6

Keypad Functions (when default programming is used) Security Functions Checking system status: STATUS (high level messages); press STATUS again

Page 7

Remote Phone Control Operation To remotely disarm system: + [1] To remotely arm in AWAY mode:

Page 8 - ‡K141170Š

Plus de documents pour Systèmes de contrôle d'accès de sécurité ADEMCO LYNXR

Voir le document ADEMCO LYNXR Guide de l'utilisateur

ADEMCO LYNXR Guide de l'utilisateur (64 pages)

Commentaires sur ces manuels

Pas de commentaire

ADEMCO LYNXR Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Systèmes de contrôle d'accès de sécurité ADEMCO LYNXR. ADEMCO LYNXR Setup guide Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Systèmes de contrôle d'accès de sécurité ADEMCO LYNXR

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO LYNXR