ADEMCO 4140XMP Spécifications télécharger pdf (Page 22)

V1l. PROGRAMMING THE SYSTEM

GENERAL PROGRAMMING PROCEDURES

The system is shippd with a set of pre-p~rmmed values

that are designed to meet the needs of many installations.

These an b changed by the installer to suti a~ctic ne~s

if desired.

In addition, Iour sefa of preprogrammed

rnmmuni=tfon dafauff values ~n al= ti Ioadad by the

installer. aach sat deaionad for a sDwific mmmuni~tk

format. These too =n ‘be changed ‘to suit the needs of a

~tiicular installation.

Changas to thase pre-programmed valuas can ba

programmd dirati~ from the ansole or fmm a mmpmer

terminal using tha 4130PC Domloading =tiara (be sura

that the software vemion uaad includes a 4140XMP menu

aeledion), an IBM rnmpatible mmptier ad a HAKS 1200

SMARTMODEM. The Iollowing pwagraphs deamibs how to

load the various default programming sets. For datailed

in~rutilons on making changes to panbular programming

fields, refer to the programming sheet at the end of this

manuaf.

For alpha consolas, English Language descriptions of the

zonas and a wstom insallar messWe (which ~~am when

tha systam is ready IO arm) -n be programmed using the

buill-in voctiulay of words (see PROGRAMMING ZONE

DESCRIPTfONS p~ag~hs Iatar in ttis sedion).

DEFAULT PROGRAMMING

There are five sats of pre-programmW defauffs available

(one standard, plus four dtierent mmmuni=tion defaults).

Any one of thasa an be Iotied into the system’s memo~.

Refar to the COMMUNICATION DEFAULT PR~RAMMING

satiion for instrutiions.

DATA PRoGRAMMING

The programming fields ara grouped into lwo sets of

addrasses. Tha first set is ameswd ~ s~n ~ pmgrammi”g

mode is antarad. To a~ess the second set of addrasses

flndi~ted On the Prog~mming fom by a .1” in front of the 2-

dqfi field addrass), press .94 wtrila in programming mode,

then press ~] plus the fimt fiald numhr desirad. Note that the

alpha mnmlas dkplW the wrds ALT PROGRAM MODE, and

the 4137/4127 mnsoias tisplay the Wd CHECK to indimte

thesmnd sat of addressas. To ratum tothafimt set of

addrasas, prass “99, then press ~] plus the fiald numbar

dasired.

To program apeclfic data flelda, prass~] plus the2-

dgfifield address, thenmakatha required ent~. Themnsofe

will Wep whan a fiati h= Men wmplete~ programmed and

will awomatimlly d~play the nexfiald in numerical order. If

the number of digits lhat you anter in the data field is less

than the maximum permitted (for axample, phona number),

thew”sele displays the last enty and waits. To proceed,

the next data field address to be programmed must be

entered manud~ (for axampla, press .05).

10 viaw the contents of a data field, press [#] plus

the2dg~field address. Tbfiati senttie swill bdisplayed,

bw no changes to these entries -n k mada.

In case of errors: If an addreas is improperly entered,

tha mnsola will dsplay FC. f a pr~ram entW is impmperiy

emerti (for axample, a lamer number than that which is

Wmittd), thewnsole display will go blank. Inatharcasa,

simp~ ra+nter the MWX numb;.

To exit programming mods, press ahher .98 or “99.

Use .98 to prevant ra-=-ss to programming mods by

inataflermde method.

.99 allows inmallar mde a~ass to

p~rammi~ mode.

PROGRAMMING STEPS

1. Enter Programming mode

ProgmmmiW retie an k anter- in ma of W w~.

1) Prass both the ~] and [#] keys a! the same time within 30

semndsafter Wwerisappfiad totb~ntrol. OR

2) Kay the insallar rode, folbwed by de~assion of CODE [8]

+ 0 + Okeys. The famo~ installer mde -n k timgad OM

in the prWram mode.

Immadiataly following ent~ into the program mode, the

follwing will ba displayad on a 5137:

-gmm Mtie

~e4127/4137mn~las display 00) ‘Rll#Viw .00

Foiloting the above display, tha system is ready 10 be

programmed forthernmmuni~tion format parameters, or

amept data entrias. To begin data antties, prs~ ~] PIUSthe

fimt field numbr desired.

2. Sat Standard Defaults

Once the Programming mods is antered, clear the system’s

memoyby pressing .97. This ensures all Wogramfialds are

sattotheir faato~ set, pre.pmgrammed valuas. if desirad,

load one of the mmmunicatbn dafauh p~ramming sats by

antering one of the folbwing de squen~s

Rder b tha PROGRAMMING COMMUNICATION DEFAULTS

setiion for futihar instrutiions if ona of the four

Wmmunimtrnn defauh programming sets is used.

3. Program the data fields

Program the appropriate phone numbers and account

numb=, as well as any othar pr~ramming fields raquired to

customize tha system to the needs of the installation. Refer

to tha PRoGMMMING FORM at t~ end of this manual,

4. Enter Zone Descriptions (5137 only)

Refer to the PR~RAMMING ZONE DESCRIPTIONS sedion

to anter zone desmiptom and a Wstom installar’s message.

5. Exit Programming Mode

When all fialds have been entered and checked, and zone

descriptors have bean assigned, exit programming mode by

pr~sing efiher .98 or “99. A s-rid entV of .99 is r~uired if

theaxit is beinodonefmm fields 1.00 anddove. Toprevem

ra.awessto Programming mode using the Installer’s code,

use “98. Tha on~ way to re-a-ss Programming mode is by

depressing both Ihe ~] and [#] keys at tha same time wkhin

30sernnds ofpower up. fitingby using .99 always allows

reant~ into Programming mode using the Installar,s code,

Efiher way of exiting w;II allow amss via downloading.

-22-

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

ADEMCO 4140XMP Spécifications Page 22

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO 4140XMP