ADEMCO 4111XM Manuel d'utilisateur télécharger pdf

ADEMCO GROUP TECHNICAL SUPPORT KNOWLEDGEBASE

STEP -BY-STEP PROCEDURE

Created: 3.27.2000

Modified: 10.31.2001

File: V10se_23.Doc

Pages: 4

Page 1 of 4

Product: Vista-10SE

Title: E2 Programming for Wireless zones.

1. Enter Programming, Installers Code (4111) + 8 + 0 or Power down then back up

& press the * + # keys simultaneously within 50 seconds.

2. Screen Displays, “INSTALLER CODE 20”

3. Press “*” + 22 & enter 2 for wireless or 4 for RF jam detection.

4. Press “*” + 56, screen displays “ENTER ZN NUM. (00 = QUIT) 01”, if using

the *58 expert mode skip to step 15.

NOTE: Wireless zones use zone numbers 10-25.

5. Screen displays, “SET TO CONFIRM? 0 = NO , 1 = YES 0” enter 1 to confirm

the serial number & loop number are correct, otherwise 0.

6. Press 10 “*”, screen displays “ZN ZT - RC IN : L”

10 00 10 RF : 1

NOTE: This is a summary screen that displays the current values for this zone. ZN

is the zone number, ZT is the zone response type, RC is the report code, IN

is the input type & L is the loop number.

6. Press “*”, screen displays “10 ZONE TYPE ZONE DISABLED” enter the

desired value for this zone.

00 = NOT USED 09 = FIRE

01 = ENTRY/EXIT #1 10 = INTERIOR W/DELAY

03 = PERIMETER 20 = ARM-STAY*

04 = INTERIOR FOLLOWER 21 = ARM-AWAY*

05 = TRBLE DAY/ALARM NIGHT 22 = DISARM *

06 = 24Hr. SILENT 23 = NO ALARM RESPONSE

07 = 24Hr. AUDIBLE

08 = 24Hr. AUX.

NOTE:

* These zone types can only be used

for wireless zones.

7. Press “*” to continue, screen displays “10 REPORT CODE 1

01 2

10” & enter the report code for this zone.

NOTE: Report code values are in hexadecimal form & range from 01-15. A = 10,

but sends a 0 to central, B = 11, C = 12, D = 13, E = 14, & F = 15.

8. Press “*” to continue, screen displays “01 INPUT TYPE RF TRANS. 3” enter

the input type for this zone.

RF = (3)Supervised RF Transmitter (ex. 5816, 5817, 5890, 5806, etc.)

UR = (4)Unsupervised RF Transmitter (ex. 5802MN, 5802MN2, etc.)

BR = (5)Button RF (ex. 5804, 5804BD, 5802)

9. Press “*” to continue, screen displays “10 INPUT S/N L”

AXXX-XXXX 1

You can type in the serial number of the device or fault it to enroll.

1 2 3 4

Résumé du contenu

Page 1

ADEMCO GROUP TECHNICAL SUPPORT KNOWLEDGEBASE STEP -BY-STEP PROCEDURE Created: 3.27.2000 Modified: 10.31.2001 File: V10se_23.Doc Pages: 4 Page

Page 2 - Pages: 4

ADEMCO GROUP TECHNICAL SUPPORT KNOWLEDGEBASE STEP -BY-STEP PROCEDURE Created: 3.27.2000 Modified: 10.31.2001 File: V10se_23.Doc Pages: 4 Page

Page 3

ADEMCO GROUP TECHNICAL SUPPORT KNOWLEDGEBASE STEP -BY-STEP PROCEDURE Created: 3.27.2000 Modified: 10.31.2001 File: V10se_23.Doc Pages: 4 Page

Page 4

ADEMCO GROUP TECHNICAL SUPPORT KNOWLEDGEBASE STEP -BY-STEP PROCEDURE Created: 3.27.2000 Modified: 10.31.2001 File: V10se_23.Doc Pages: 4 Page

Commentaires sur ces manuels

Pas de commentaire

ADEMCO 4111XM Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Systèmes de contrôle d'accès de sécurité ADEMCO 4111XM. 1. Enter Programming, Installers Code (4111) + 8 + 0 or Power down Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO 4111XM