ADEMCO 4140XMPT2 Manuel d'utilisateur télécharger pdf

N5944-9PR 4/96 (See Instructions N5944-9)

4140XMPT2 PROGRAMMING FORM

Some fields are programmed for each partition (shown as shaded fields). See the PARTITION-SPECIFIC section for

programming these fields. Standard default (*97) values are shown in brackets [ ], otherwise default = 0.

Fields bordered by dotted line can be programmed using the #93 Menu mode.

*00 INSTALLER CODE | | |

Enter 4 digits, 0-9 [4140]

ASSIGN RESPONSE TYPE FOR ZONES

(Enter 00-10; see Response Types below) see fields 1*01-1*09 to program

response types for zones 28-87.

*02 *03 *04 *05

1 | 9 | 17 | 25 |

2 | 10 | 18 | 26 |

3 | 11 | 19 | 27 |

4 | 12 | 20 | 0|0

5 | 13 | 21 | 97 | polling loop short

6 | 14 | 22 | 95 | (1+✱ panic)

7 | 15 | 23 | 96 | (3+ # panic)

8 | 16 | 24 | 99 | (✱+ # panic)

RESPONSE TYPES: 00 = Disabled zone; 01 = Entry/Exit #1;

02 = Entry/Exit #2; 03 = Perimeter; 04 = Interior Follower;

05 = Day/Night; 06 = 24 hour Silent Alarm; 07 = 24 hour Audible Alarm;

08 = 24 hour Auxiliary; 09 = Fire; 10 = Interior, Delay; 20 = arm stay; 21

= arm away; 22 = disarm; 23= no alarm response

*09 ENTRY DELAY #1 |

*10 EXIT DELAY #1 |

*11 ENTRY DELAY #2 |

*12 EXIT DELAY #2 |

*13 ALARM SOUNDER DURATION |

*14 ZONE 9 FAST/SLOW RESPONSE

1=fast; [0= slow]; "0" for UL.

*15 KEYSWITCH ASSIGNMENT

Enter partition in which keyswitch used, 1-8; [0=disable]

*16 CONFIRMATION OF ARMING DING

*17 AC POWER LOSS SOUNDING

1=yes; [0=no]

*18 AC POWER LOSS ALARM

1=yes; [0=no]

*19 AC RANDOMIZE

1=randomize 10-40 min.; [0=no]

*20 PHONE MODULE ACCESS CODE | |

Enter 01-09 for 1st digit; 11 (for ✴) or 12 (for #) for [00] [11]

2nd digit. To disable phone module, enter 1st digit =00 & 2nd digit =

*21 DISABLE FIRE TIME-OUT

1=no timeout; [0=fire timeout]

*22 CONSOLE PANIC ENABLES 95 96 99

*23 MULTIPLE ALARMS

*24 EXPANSION ZONE (RF, RPM) TAMPER DISABLE

1=disable; [0=enable]

*25 BURG.TRIGGER FOR RESPONSE TYPE 8

[1=enable]; 0=disable

*26 INTELLIGENT TEST REPORTING

Set "0" for UL 1=yes, (no report sent if any other report was

recently sent); [0=no]

*27 TEST REPORT INTERVAL [024] | |

Enter interval in hours, 001-199; 000=no report ; Max. 024 for UL.

*28 POWER UP IN PREVIOUS STATE

[1=yes] 0=no; "1" for UL.

*29 QUICK ARM

*30 TOUCH-TONE OR ROTARY DIAL

1=TouchTone; [0=rotary]

*31 PABX ACCESS CODE | | | |

00-09; B-F (11-15)

*32 PRIM. SUBS. ACCT # | | | |

*33 PRIMARY PHONE NUMBER

Enter 0-9 for each digit

*34 SECONDARY PHONE NUMBER

Enter 0-9 for each digit

*35 DOWNLOAD PHONE No.

Enter 0-9 for each digit

*36 DOWNLOAD ID No.

| | | | | | |

Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]

*37 DOWNLOAD COMMAND ENABLES

Dialer System Not Remote Remote Remote Upload

Shutdwn Shutdwn Used Bypass Disarm Arm Program

See field 1*53 for Callback disable option; [1=enable]; 0=disable; For UL

installations, all options must be disabled.

*38 INHIBIT BYPASS OF A ZONE |

*39 OPEN/CLOSE REPORT FOR INSTALLER

*40 OPEN/CLOSE REPORTING FOR KEYSWITCH

1=enable; [0=disable]

*41 EOLR DISABLE (Zones 2-8)

[1=N.C.loops]; 0=EOLR supervision; Must be "0" for UL.

*42 DIAL TONE PAUSE

[0=5 seconds]; 1=11 seconds; 2=30 seconds; Must be "0" for UL.

*43 DIAL TONE DETECTION

[1=wait for true dial tone]; 0=pause, then dial

*44 RING DETECTION COUNT

01-14; 15=answering machine; [00=no detection]

*45 PRIMARY FORMAT

[0=Low Speed]; 1=Contact ID; 2=Ademco High Speed;

3=Ademco Express

*46 LOW SPEED FORMAT (Primary)

[0=Ademco Low Speed]; 1=Sescoa/Radionics

*47 SECONDARY FORMAT

[0=Low Speed]; 1=Contact ID; 2=Ademco High Speed;

3=Ademco Express

*48 LOW SPEED FORMAT (Sec.)

[0=Ademco Low Speed]; 1=Sescoa/Radionics

*49 CHECKSUM VERIFICATION

1=yes; [0=no] Prim Scndry

*50 SESCOA/RADIONICS SELECT

1=Sescoa; [0=Radionics]

*51 DUAL REPORTING

1=yes; [0=no] If used with Spilt Reporting "1" option (1*34), alarms

go to both primary & secondary numbers, while all other reports go

to secondary only. If used with Split Reporting "2" option,

open/close and test messages go to both lines, while all other

reports go to primary.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - 4140XMPT2 PROGRAMMING FORM

N5944-9PR 4/96 (See Instructions N5944-9)4140XMPT2 PROGRAMMING FORMSome fields are programmed for each partition (shown as shaded fields). See the P

Page 2

Page 2*52 STANDARD/EXPANDED REPORT FOR PRIMARY Alarm Rstr Bypass Trbl Opn/Cls Low Bat[0=standard]; 1=expanded; Note: Expanded overr

Page 3 - 1*01 1*02 1*03 1*04 1*05

Page 32nd Page Programming Fields (press *94)ASSIGN RESPONSE TYPE FOR ZONES (Enter 00-10; see Response Types below)1*01 1*02 1*03 1*04 1*0528 | 33

Page 4 - 3rd Page Programming Fields

Page 43rd Page Programming Fields(press *94) PARTITIONING SETUP FIELDSRefer to the PARTITION-SPECIFIC program fields forprogramming each partition’s v

Page 5 - PARTITION-SPECIFIC FIELDS

Page 5PARTITION-SPECIFIC FIELDS(Duplicate this page for each partition in the installation.)To program these fields,1. Press *91 to select a partition

Page 6

Page 6PARTITION-SPECIFIC FIELDS(Duplicate this page for each partition in the installation.)To program these fields,1. Press *91 to select a partition

Page 7

Page 7SUMMARY OF PROGRAMMING COMMANDS• To enter program mode, enter installer code + [8] + [0] + [0]• To set standard defaults, press *97• To set comm

Page 8 - – NOTES –

Plus de documents pour Systèmes de contrôle d'accès de sécurité ADEMCO 4140XMPT2

Voir le document ADEMCO 4140XMPT2 Manuel d'utilisateur

ADEMCO 4140XMPT2 Manuel d'utilisateur (4 pages)

ADEMCO 4140XMPT2 Manuel d'utilisateur (68 pages)

ADEMCO 4140XMPT2 Manuel d'utilisateur (132 pages)

Voir le document ADEMCO 4140XMPT2 Manuel d'installation

ADEMCO 4140XMPT2 Manuel d'installation (54 pages)

Commentaires sur ces manuels

Pas de commentaire

ADEMCO 4140XMPT2 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Systèmes de contrôle d'accès de sécurité ADEMCO 4140XMPT2. 4140XMPT2 PROGRAMMING FORM Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Systèmes de contrôle d'accès de sécurité ADEMCO 4140XMPT2

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité ADEMCO 4140XMPT2